| Item Picture |
Item Descrition |
Price |
 |
Challenger Flip-Up Nose Cone Hinge Kit – Enables the aircraft owner to quickly and easily access the inside of the front of the aircraft for maintenance and repair. This is one of the most useful after-market modifications for the Challenger ultralight. Includes the custom machined hinge, rivets, cowl straps, and instructions. See the Modifications page for more details. |
$185.00 |
 |
Challenger Electrical Station – Open Chassis electrical system for Challenger made from sturdy .080 aluminum. With battery connection posts and terminal strips for wiring a Challenger Ultralight instrument panel and remote engine sensors. Includes 4 vibration absorbing mounting feet. 8 station surface mount fuse panel for Master circuit plus 7 accessory circuits. Includes hidden anti-theft switch. Also includes 100 assorted electrical connectors to complete aircraft wiring. Includes 8 fuses plus 16 spares. Custom labelled for your aircraft. See Accessories Page for more details. |
$200.00 |
 |
Do It Yourself Electrical Component Kit – All the components you will likely need to wire up your ultralight aircraft. Includes 8 station fuse block, a selection of 25 fuses, 2 screw down terminal buses, 2 screw down terminal junction blocks, 2 push-in junction blocks, 8 heavy duty toggle switches, a push button start switch, 24 vinyl toggle switch caps in 6 colours, and a selection of 250 electrical connectors. |
$200.00 |
 |
Avionics Shelf – Simplifies the installation, wiring, and trouble shooting of the electrical system for any Challenger. Measures 16″ x 6″ wide. Ready to install with rivets into nose of Challenger on existing framework. Note: for more pictures and information on this option, go to the Instrument Panel page. |
$40.00 |
 |
Avionics shelf with 5 Terminal Strips and Bus Bars installed including Common Power Bus Bar, Common Ground Bus Bar, 12 Station Terminal Strip for Engine Sensors, a Terminal Strip for Switched Outputs, and a heavy duty 4 Station Terminal Strip for connecting the Voltage Regulator to the Battery and Alternator Cables. All custom labelled for your specific application. Send us your voltage regulator and starter solenoid and we will mount these also.Note: for more pictures and information on this option, go to the Instrument Panel page. |
$90.00 |
 |
8 Station Fuse Box – Compact surface mount fuse holder with 8 circuits for ATC style fuses. 30 Amp capacity per circuit. 1/4″ male tabs out bottom side. Ideal for surface mounting on panel. Comes with clear snap on cover and mounting screws. |
$30.00 each |
 |
8 Station Terminal Strip Bus Bar – Compact surface mount terminal strip with jumpers to make entire unit a single common circuit bus bar. Excellent for use as a common ground bus bar or common positive source bus bar. Surface mounts with 4 mounting holes. 16 screw terminals with #6 size screws. 3-5/8″ long x 7/8″ wide x 1/2″ high. Can be used as a standard junction block if jumper strip is removed. |
$7.50 each |
|
8 Station Terminal Strip Junction Block – Compact surface mount electrical terminal strip. Excellent for use as junction block to neatly join circuits at a common point. Surface mounts with 4 mounting holes. 16 screw terminals with #6 size screws. 3-5/8″ long x 7/8″ wide x 1/2″ high. |
$6.00 each |
 |
12 Station Push In Terminal Strip – terminal strip for 14 to 20 gauge wires. Simply strip end of wire, push in and screw down. No need for wire connectors. Excellent for use as a junction block. Surface mounts with #4 screw size hole between each circuit. 3-3/4″ long x 5/8″ wide x 5/8″ high. Can be cut up into smaller sections. |
$6.00 each |
 |
ATO/ATC Style Fuses – for above Electrical Station and Fuse Box. Come in the following Amp ratings: 1,2,3,5,10,15,20,25,30. |
$0.25 each |
 |
Large Terminals – 3/8″ threaded terminals to connect 4 gauge electrical cables from battery to aircraft electrical system. One each in red (positive) and black (negative). Comes with nuts and lock washers, mounting screws, and 6 matching ring terminals to adapt to 10 gauge wire. |
$20.00/set |
 |
Heavy Duty Toggle Switch – Metal toggle operated electrical switch, 2 position ON / OFF. 25 Amp capacity at 12 volts. Screw terminal connections. Includes threaded mounting neck with panel nut and washer. |
$7.50 each |
 |
Coloured Vinyl Toggle Switch Covers – package of 24 in 6 colours – red, white, black, blue, grey and yellow. These fit tightly over the metal switch toggle and enable the switch functions to be colour coded adding safety and ease of use to the instrument panel switches. Plus they make the instrument panel look great! |
$10.00/pack |
 |
Coloured Vinyl Mini Toggle Switch Covers – package of 15 in 3 colours – red, black, and yellow. These fit tightly over the metal switch toggle for 0.10″ diameter mini toggles and enable the switch functions to be colour coded adding safety and ease of use to the instrument panel switches. Plus they make the instrument panel look great! These also fit most mini toggles found on radios, intercoms, transponders and other electrical instruments. |
$5.00/pack |
|
TIE DOWN RINGS – Stainless Steel Tie Down Rings for adding to strut tubes. 1/4 inch holes match mounting bolt on Challenger. Includes extra long mounting bolts to accommodate additional length. |
$50.00/pair |
 |
All Metal Fuel Line Tee Fitting for 3/8″OD x 1/4″ fuel line – These are All Brass fittings that will not crack due to heat, UV light or exposure to fuel. Double barb design ensures strong connection without the need for clamps. This fitting is used to split your fuel line to supply the two carburetors. 1 required for Challenger kit. |
$5.00 each |
|
All Metal Fuel Line Reducing Tee Fitting for 3/8″OD x 1/4″ fuel line with smaller barb off the side for 1/4″OD x 1/8″ID primer line- These are All Brass fittings that will not crack due to heat, UV light or exposure to fuel. Double barb design ensures a very strong connection without the need for clamps. This fitting enables you to tap off the main fuel supply line to run the smaller primer tube to the primer pump. 1 required for Challenger kit. |
$3.50 each |
|
All Metal Primer Line Tee Fitting for 1/4″OD x 1/8″ fuel primer line- These are All Brass fittings that will not crack due to heat, UV light or exposure to fuel. Double barb design ensures strong connection without the need for clamps. This tee fitting enables you to split the primer line to supply the two carburetors. 1 required for Challenger kit. |
$3.50 each |
 |
LANDING LIGHT – Streamlined 12 volt DC landing light with mounting bracket and fasteners. |
$25.00/each |
|
Aluminum Instrument Panel Blank – Made from .080″ aluminum and cut to fit Challenger cockpit. No gauge holes or switch holes cut. 20 inches wide x 12″ high. Unfinished aluminum. |
$50.00 |
|
Aluminum Instrument Panel with Holes Cut – Made from .080″ aluminum and cut to fit Challenger cockpit. Gauge holes and switch holes cut, deburred and ready to mount gauges. 20 inches wide x 11″ high. Primed and painted aluminum. For mounting brackets and anti-vibration mounts installed, add $60.00. |
$200.00 |
|
Aluminum Instrument Panel with Gauges Mounted – Made from .080″ aluminum and cut to fit Challenger cockpit. Gauge holes and switch holes cut, deburred and customer supplied gauges installed with stainless steel socket head cap screws. 20 inches wide x 12″ high. Aluminum primed and painted flat black. Mounting bracket installed with anti vibration mounts. |
$400.00 |
 |
VIBRATION ISOLATION MOUNTS – Male to Male 1/4-20 threaded fasteners for mounting instrument panel. |
$7.50/each |
|
Door Edging – Black U-shaped door edging as supplied in the Challenger kit. Used to cover the sharp edges of the lexan doors, wind screen, and the instrument panel. Has an internal bead of adhesive to glue it to the lexan. Prevents the lexan from chafing the paint and giving pilots nasty cuts. |
$20.00/25 ft |
